Bits n Bobs Parts For Sale...

Moderator: VTRDark

Post Reply
User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Bits n Bobs Parts For Sale...

Post by MacV2 » Wed Oct 10, 2018 11:57 am

Come on down parts sale all stock must go to make room for fresh deliverys... :lol: :lol:
First come, first dibs by time of post or direct PM...Frank will be watching...

Image

Phone holder with mount for stearing stem...Think its for an i-phone but has a foam inner which could be altered to fit other phones...
The space in side the foam is 150 x 70mm. £5 + shipping.

Image
Image

Renthal Utra low bars... 758 Drilled for Storm control lugs...SOLD

Image

Re padded & re covered Std seat...Coverd with alcantara type meterial which whilst claims it's showerproof definitely ain't waterproof, I have used this on one of my bikes & I know it holds water when it gets a good soaking... The rear part is darker as it's not sun faded due to having a seat hump on. Small tare/wear on front right corner, I can supply a patch to repair this if required.... £25 + shipping.

Image
Image

Alternator cover c/w coil, few marks to cover but no road rash, coils all fairly good colour no blacking...SOLD

Image

So the rest of it...

Pair front footrest hangers compleate...£60 + shipping ( back up for sale as FB messer has not been back in touch...)

Starter motor, untested could do with a refurb as bolt is a bit coroded... £10 + shipping.

Sprocket carrier...SOLD

1x Rear down pipe...£5 + shipping.

Rear brake carrier...SOLD

Pair small flush mount indis...£5 + shipping

2x Short velocity stack, all tabs & screws good order...£5 each+ shipping

2x std fork top shrouds...£5 the pair + shipping

Aftermarket LED rear light, will not fit std bodywork but might do some one a turn if doing a bobber/hack job or something... £5 + shipping

Snail type horn...£3 + shipping

Std horn... £2.50 + shipping

2x std indi relays...£2.50 each+ shipping

1x carb rubber... £2.50 + shipping

Petcock rubber shroud thingy...£3 posted UK mainland...

Following items are free if anyone wants them, cover shipping costs...

CBR 600 ? front brake lever...CLAIMED...



All items where shipping required Std PO rates upto 2kg small parcle £2.95

Over 2kg I will get a quote before sending...
Last edited by MacV2 on Sat Nov 17, 2018 10:57 am, edited 5 times in total.
Lowering the tone since 2007...

User avatar
sirch345
Site Admin
Posts: 17337
Joined: Mon Aug 25, 2003 9:35 pm
Location: Cornwall, UK

Re: Bits n Bobs Parts For Sale...

Post by sirch345 » Thu Oct 11, 2018 2:55 pm

Some good prices there Mac :thumbup:

GLWS

Chris.
A closed mouth gathers no foot. :thumbup:

User avatar
popkat
Posts: 2462
Joined: Sat Apr 28, 2012 8:32 am
Location: Devon

Re: Bits n Bobs Parts For Sale...

Post by popkat » Thu Oct 11, 2018 6:50 pm

Is there the black plastic cap that goes in the top of the steering stem in among that lot ? good condition with no scratches of course :wink:




.
http://www.bidefordmotorcycles.co.uk
2014 CRMC Post classic Superbike champion.
2014 CRMC Post classic senior production champion. On a Suzuki Katana 1100
My bikes, Firestorm, Yamaha MT10SP, 2 x Honda RC24 road and race, Popup Katana and a some XJ600's

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Thu Oct 11, 2018 7:52 pm

popkat wrote:
Thu Oct 11, 2018 6:50 pm
Is there the black plastic cap that goes in the top of the steering stem in among that lot ? good condition with no scratches of course :wink:


I might have one somewhere...will get Frank to check...
Lowering the tone since 2007...

User avatar
popkat
Posts: 2462
Joined: Sat Apr 28, 2012 8:32 am
Location: Devon

Re: Bits n Bobs Parts For Sale...

Post by popkat » Sat Oct 13, 2018 2:26 pm

MacV2 wrote:
Thu Oct 11, 2018 7:52 pm
popkat wrote:
Thu Oct 11, 2018 6:50 pm
Is there the black plastic cap that goes in the top of the steering stem in among that lot ? good condition with no scratches of course :wink:


I might have one somewhere...will get Frank to check...

And a good undamaged handlebar end weight :)



.
http://www.bidefordmotorcycles.co.uk
2014 CRMC Post classic Superbike champion.
2014 CRMC Post classic senior production champion. On a Suzuki Katana 1100
My bikes, Firestorm, Yamaha MT10SP, 2 x Honda RC24 road and race, Popup Katana and a some XJ600's

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Sat Oct 13, 2018 4:28 pm

popkat wrote:
Sat Oct 13, 2018 2:26 pm
MacV2 wrote:
Thu Oct 11, 2018 7:52 pm
popkat wrote:
Thu Oct 11, 2018 6:50 pm
Is there the black plastic cap that goes in the top of the steering stem in among that lot ? good condition with no scratches of course :wink:


I might have one somewhere...will get Frank to check...

And a good undamaged handlebar end weight :)



.

Forgot about this & I was in the cave today...oops! sorry...

As for the end weights I'll have to check...Not 100% sure I have a decent one as I was feking about trying to sort out the bar end on Custurd the other week...The last fall had bent the screw...& the previous fall snapped the inner weight off...
Lowering the tone since 2007...

User avatar
popkat
Posts: 2462
Joined: Sat Apr 28, 2012 8:32 am
Location: Devon

Re: Bits n Bobs Parts For Sale...

Post by popkat » Sat Oct 13, 2018 6:23 pm

MacV2 wrote:
Sat Oct 13, 2018 4:28 pm
popkat wrote:
Sat Oct 13, 2018 2:26 pm
MacV2 wrote:
Thu Oct 11, 2018 7:52 pm



I might have one somewhere...will get Frank to check...

And a good undamaged handlebar end weight :)



.

Forgot about this & I was in the cave today...oops! sorry...

As for the end weights I'll have to check...Not 100% sure I have a decent one as I was feking about trying to sort out the bar end on Custurd the other week...The last fall had bent the screw...& the previous fall snapped the inner weight off...

No worries not a mega rush, I scuffed my right bar weight when I borrowed it on to the race bike and had a little tip off last year, after that I put different type of bar ends on but had to put the original back on my storm, so it looks like I've crashed that one when I haven't. It's just a little scuffed that's all but it notices.
The Plastic cap/bung is for my VFR road bike which it's missing from and 99% sure it's exactly the same part numbers.



.
http://www.bidefordmotorcycles.co.uk
2014 CRMC Post classic Superbike champion.
2014 CRMC Post classic senior production champion. On a Suzuki Katana 1100
My bikes, Firestorm, Yamaha MT10SP, 2 x Honda RC24 road and race, Popup Katana and a some XJ600's

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Sun Oct 14, 2018 9:08 am

Malc O'Pop... incoming PM... :thumbup:
Lowering the tone since 2007...

User avatar
popkat
Posts: 2462
Joined: Sat Apr 28, 2012 8:32 am
Location: Devon

Re: Bits n Bobs Parts For Sale...

Post by popkat » Sun Oct 14, 2018 10:53 am

MacV2 wrote:
Sun Oct 14, 2018 9:08 am
Malc O'Pop... incoming PM... :thumbup:

:thumbup:



.
http://www.bidefordmotorcycles.co.uk
2014 CRMC Post classic Superbike champion.
2014 CRMC Post classic senior production champion. On a Suzuki Katana 1100
My bikes, Firestorm, Yamaha MT10SP, 2 x Honda RC24 road and race, Popup Katana and a some XJ600's

User avatar
freeridenick
Posts: 878
Joined: Fri May 23, 2014 12:30 pm
Location: Derbyshire

Re: Bits n Bobs Parts For Sale...

Post by freeridenick » Mon Oct 22, 2018 11:42 am

PM on its way Mac.

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Mon Oct 22, 2018 2:50 pm

freeridenick wrote:
Mon Oct 22, 2018 11:42 am
PM on its way Mac.
PM back at ya...
Lowering the tone since 2007...

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Wed Nov 14, 2018 7:31 pm

Updated...

Franks been busy today large order going out to Sweeden... :thumbup:
Lowering the tone since 2007...

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Sat Nov 17, 2018 10:58 am

MacV2 wrote:
Wed Nov 14, 2018 7:31 pm
Updated...

Franks been busy today large order going out to Sweeden... :thumbup:
Another update...
Lowering the tone since 2007...

bobbler
Posts: 87
Joined: Mon Aug 13, 2018 10:54 am
Location: Co. Durham

Re: Bits n Bobs Parts For Sale...

Post by bobbler » Sat Nov 17, 2018 11:32 am

Will the flush fit indis fit the standard front fairings Mac?

User avatar
MacV2
Posts: 13378
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Bits n Bobs Parts For Sale...

Post by MacV2 » Sat Nov 17, 2018 11:37 am

bobbler wrote:
Sat Nov 17, 2018 11:32 am
Will the flush fit indis fit the standard front fairings Mac?

I dunno...I 'll have a look & get back to ya...
Lowering the tone since 2007...

Post Reply