My 2 into 1 project now with dyno print out

Kev L · Post by **Kev L** » Wed May 23, 2012 4:50 pm

Did you see this one Lloydie -
http://www.ebay.co.uk/itm/2000-HONDA-VT ... 4d017fd7b0

VTRDark · Post by **VTRDark** » Wed May 23, 2012 5:21 pm

It's a good idea being able to hot swap exhausts.

So you can switch between the 2 into 1 back to 2 again.

I'm quite surprised how rough the bore of the Y piece is. It looks like the rear pipe partially blocks the front.

Have Fun.

(:-})

seb421 · Post by **seb421** » Wed May 23, 2012 5:26 pm

Kev L wrote:Did you see this one Lloydie -
http://www.ebay.co.uk/itm/2000-HONDA-VT ... 4d017fd7b0

6,500 my butt looks like its been ragged, dropped and painted badly including the can. no mirrors either this boy fancies his self as some roads racer

Kev L · Post by **Kev L** » Wed May 23, 2012 5:29 pm

I was only using it to show the 2 into 1 exhaust system. I didn't read the rest of it.

lloydie · Post by **lloydie** » Wed May 23, 2012 5:32 pm

Ohhhh I like the silver wheels

The headers are the same as the other one side caped off lol

lloydie · Post by **lloydie** » Wed May 23, 2012 5:34 pm

cybercarl wrote:It's a good idea being able to hot swap exhausts. So you can switch between the 2 into 1 back to 2 again. I'm quite surprised how rough the bore of the Y piece is. It looks like the rear pipe partially blocks the front.

Have Fun.

(:-})

and that one had been cleaned up lol
They are even worse standard

edds11 · Post by **edds11** » Wed May 23, 2012 8:22 pm

+1 on loydie, the outlet for my offside is like a slit about 15mm wide where its been filled with the inlet and other outlet, mr honda should be ashamed......soon to be changed though

if I could write mmooohhaahhaa in a menacing way I would

edds11 · Post by **edds11** » Tue May 29, 2012 9:19 pm

I can know say MMOOOHHHAAAHHHAAAAA, two silencers gone, one 60mm wyleco titanium sits in place of one of them.... sounds saweeet, goes saweeet, save up some penny's for a rolling road visit and Bob's your Uncle.

Flatline · Post by **Flatline** » Tue Sep 10, 2013 12:34 pm

Wow, Lloydie, where can I get one of those removable thumbs from

lloydie wrote:Modified my other headers today in to a 2-1 .i just need to get a new rear down pipe to collector gasket before I can fit them .

lloydie · Post by **lloydie** » Tue Sep 10, 2013 2:51 pm

eBay . Very cheap from Hong Kong

Kev L · Post by **Kev L** » Tue Sep 10, 2013 10:56 pm

lloydie wrote:eBay . Very cheap from Hong Kong

I think their British distributor is in Nothumberland!!!!!

AMCQ46 · Post by **AMCQ46** » Tue Sep 10, 2013 11:00 pm

Kev L wrote:
lloydie wrote:eBay . Very cheap from Hong Kong
I think their British distributor is in Nothumberland!!!!!

Very very very subtle

Kev L · Post by **Kev L** » Tue Sep 10, 2013 11:05 pm

Subtle is my middle name. As much as a flying house brick!!

lloydie · Post by **lloydie** » Tue Sep 10, 2013 11:11 pm

:thumbup;

Flatline · Post by **Flatline** » Wed Sep 11, 2013 7:22 am

Would laugh at your witty comments but I have a thumbping headache

VTR1000.ORG